Secret Room by Earthborn

Claypaint

Do you need a primer?

In most cases, no primer is needed before applying Claypaint. However, in certain situations we recommend using the following: • Wall Glaze: For persistent residue or to stabilise sandy or powdery surfaces • Isolating Primer: to cover stains (nicotine, water), silicone/acrylic sealants, metal edges or nails • Bonding Primer: for unknown substrates, patchy surfaces, or areas where previous coatings have been removed. Promotes adhesion and evens out differences in surface absorbency (porosity) Note: Using a primer introduces an additional coating that is less vapour permeable than Claypaint, which may slightly reduce the overall breathability of the finished coating. VOC Content: Less than 0.1% (trace only) < 0.5g/l (0.15g/l) Before you start For best results, ensure surfaces are clean, sound, and free from dust, grease, or loose material. The moisture content of the surface needs to be less than 15% before painting. Repair cracks with a filler of similar porosity to avoid visible mark (“grinning”). For lime, natural, or mineral surfaces, a breathable, flexible filler is recommended. Do not apply at temperatures below 8°C.

How to apply

• For highly absorbent surfaces such as fresh plaster, apply a mist coat diluted with up to 10% clean water first • When painting darker colours, apply the final coat generously in one direction to achieve an even finish • Always check colour accuracy before applicationSlight colour variations may occur between batches due to the natural ingredients used • Paint from different batches should be mixed together before use • If applying a top coat of Wall Glaze, do a test area first as it may deepen the overall shade • Don’t worry if it looks patchy while drying, that’s normal! Let it dry fully before applying another coat, otherwise you may get a patchy finish 1. Slightly dampen the roller or brush before use 2. Stir the paint thoroughly, getting right down to the bottom of the tin 3. Pour into a paint tray and apply using a short or medium pile roller 4. Work in W or M shaped strokes for even coverage 5. Work in smaller, manageable sections, keeping a wet edge, to avoid visible framing around cut-in areas. This is especially important for darker colours. 6. Let each coat dry completely before applying the next On previously painted surfaces, one coat may be enough Spray application Airless pressure: ≥120 bar (approx. 1740 psi) Flow rate: 2.5 litres/min Coating thickness: 250–300 g/m² Maximum nozzle size: 0.68 mm (527 tip) Recommended nozzle size: 0.58 mm (523 tip) Filter/Mesh: Use appropriate filtering to prevent nozzle clogging Dilution: Can be thinned with up to 7% water Caring for your paintwork To keep your paint looking its best, clean surfaces gently with a soft cloth or sponge and water. Avoid abrasive cloths or harsh detergents, as these can leave visible marks or damage the finish. It’s often possible to remove surface marks using a pencil eraser or very fine emery paper, we’d recommend testing on a small, hidden spot first. Storage and disposal Store the paint in a cool, frost free place with the lid tightly closed. • Don’t pour unused paint down the drain or into watercourses. Let it dry out and follow local disposal rules • Recycle empty tins where possible • Find out how to clean brushes & rollers here

Where to use it

Vapour Permeability Class: Class 1 (Highly vapour permeable) Earthborn Claypaint is ideal for interior walls and ceilings, and particularly suitable for; • Lime plaster and breathable substrates • Older buildings and heritage properties • Conservation and restoration projects • Passive houses and eco builds • Damp or moisture-prone areas • Areas exposed to heat, such as behind wood burners and on radiators • Public and sensitive spaces including museums, galleries and churches Suitable substrates include lime, clay, cob and earth plasters, gypsum plaster, brick, wallpaper, wood, most mineral surfaces, and previously painted surfaces, provided they are sound, clean and dry.

Working with new plaster or lime

Fresh plaster and lime surfaces are strongly alkaline, so a little patience goes a long way. Before painting: • Ensure the substrate is fully cured, dry, and no longer chalking. The surface should show no ongoing chemical activity • Recommended curing times: o Gypsum plaster: ≥1 month o Lime plaster: ~1 month per 5 mm thickness (e.g., 25mm ≈ 5 months) • Do not paint with coloured shades if pH ≥10, as pigments may be affected. White Clay and Marbles are fine when pH ~11–12 • Wipe powdery residue with a damp cloth

Eco Chic

How to apply

• Stir thoroughly before use • Apply with a brush or roller • Allow 6–12 hours between coats depending on room temperature and humidity. To create decorative effects, apply a contrasting base coat followed by the chosen topcoat colour. Sand back areas to reveal the base colour • Fully cured after approximately 10 days • Finish with a protective coating of Earthborn Furniture Wax for added durability We recommend finishing with a protective coating of Earthborn Furniture Wax for added durability. To keep your paint looking its best, clean surfaces gently with a soft cloth or sponge and water. Avoid abrasive cloths or harsh detergents, as these can leave visible marks or damage the finish. • Safety first Synthetic preservative contains 1,2-benzisothiazol-3(2H)-one and a reaction mass of 5-chloro-2-methyl-1,2-thiazol-3(2H)-one and 2-methyl-1,2-thiazol-3(2H)-one (3:1). May produce an allergic reaction. IF IN EYES: rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do so. Continue rinsing. IF ON SKIN: wash with plenty of soap and water. Wear a suitable face mask/protective equipment if dry sanding or using spray equipment. Always keep the product out of reach of children. Please refer to the Material Safety Data Sheet for full details.

Where to use it

Earthborn Eco Chic is perfect for: • Previously painted or unpainted wooden furniture • Can also be used on interior walls for smaller decorative projects requiring a low-odour, eco friendly, durable finish Before you start For best results, ensure all surfaces are clean, dry and free from dust, grease or wax. Previously painted furniture should be lightly sanded to provide a key. No primer is needed on previously painted surfaces. For untreated wood, prime with Eco Chic thinned with 10-20% water. Do not apply at temperatures below 8°C. What's inside? Eco Chic contains Water, fillers (various clays, chalk, kaolin), binder (based on plant-derived acetic acid and ethylene), thickener (methylcellulose), pigments (some colours contain titanium dioxide), and <0.1% synthetic preservative* (isothiazolinone mixture). Eco Chic Key Facts Coverage: Approximately 10 m² per litre (dependent on substrate absorbency and application technique) Drying time: 6–12 hours between coats; fully cured in ~10 days ² Colours: Available in our classic colour range, including TiO2-free and TiO2/Colourant-free options Sheen: ~ 2% Finish: Ultra flat matt finish Pack Size 750 ml Scrub resistance: Class 3, can be sealed with Earthborn Furniture Wax for extra durability Thinner: Water (10-20%) Tools: Brush or roller

Eggshell No. 17

How to apply

• Stir thoroughly before use • Apply 2 coats of undiluted Eggshell No.17 for best results • Sand lightly between coats • Can be applied by brush, roller or spray gun (if using pressure pot, thin with 10–30% water) What’s inside? Water, Acrylic Binder (VAE/Soft Emulsion), Pigments (incl. Titanium Dioxide), Fillers (China Clay, Dolomite), Preservative* (Isothiazolinone Mixture), Thickener (Methylcellulose), Dispersant (Phosphate), pH Modifier (Sodium Hydroxide). Breathability and VOC’s Moisture Vapour Transmission Rate (MVTR): 513 g/m² per day Water Vapour Resistance (Sd-Value): 0.06m (0.077m over Multi Purpose Primer) Vapour Permeability Class: Class 1 (Highly vapour permeable) VOC Content: < 0.1% (trace only) < 0.5g/l Spray application A few important notes: Airless pressure: 96 bar (approx. 1440 psi) Increase as needed to • For best results, use Earthborn achieve a smooth, Multi Purpose Primer before even spray. applying Eggshell No.17 Flow rate: 1.5-2.5 litres/min Coating thickness: 155-235 g/m² • Allow the first coat to dry Recommended nozzle size: 0.43 mm (517 tip) fully before recoating; applying Filter/Mesh: 60–100 mesh, additional coats too soon may cause tackiness depending on application. • Avoid painting in high humidity, Dilution: Dilute with up to 10% as the paint may not cure water, depending on properly temperature, humidity, and substrate conditions. Use the Caring for your paintwork minimum amount necessary to maintain To keep your paint looking its best, clean good sprayability. surfaces gently with a soft cloth or sponge and water. Avoid abrasive cloths or harsh detergents, Airless spray only. HVLP and other low-pressure as these can leave visible marks or damage the finish. systems are not recommended for this product.

Where to use it

Tools: Brush, roller or spray gun Eggshell No.17 is perfect for: • Interior woodwork such as doors, window frames, shelving and panelling • Skirting boards, trim and smooth-planed wood • Wooden furniture & kitchen cabinets • Not suitable for floors or other heavy-duty surfaces Before you start For best results, ensure wood surfaces are sound, clean, dry, and free from dust, grease, or loose/ flaking paint. Make sure to sand surfaces lightly before application and remove any defective wood. If needed treat knots with a suitable knotting solution. Prime bare or previously painted wood with Earthborn Multi Purpose Primer. Do not apply in temperatures below 8°C.

Lifestyle

How to apply

• Stir thoroughly before use • Apply 2 coats with a brush, roller or spray gun • For porous surfaces (e.g. bare plaster), thin first coat with water (four parts paint to one part water) • Allow to dry between coats A few important notes: • Make sure the walls are dry and proper surface preparation has been done • For porous surfaces such as new plaster, apply a mist coat (four parts paint mixed with one part water) • Stir the paint well before and during use • Follow the drying times between coats Caring for your paintwork To keep your paint looking its best, clean surfaces gently with a soft cloth or sponge and water. Avoid abrasive cloths or harsh detergents, as these can leave visible marks or damage the finish. Storage and disposal • Store in a cool, dry, frost-free place with the lid tightly closed • Shelf life of unopened containers exceeds 6 months • Dispose of any surplus paint safely, following local disposal guidelines • Recycle empty tins where possible • Find out how to clean brushes & rollers here Breathability and VOC’s Moisture Vapour Transmission Rate (MVTR): 225g/m² /day Water Vapour Resistance (Sd-Value): 0.091m Vapour Permeability Class: Class 1 (Highly vapour permeable) VOC Content: Less than 0.1% (trace only) / < 0.5 g/L Spray application Airless pressure: 96 bar (approx. 1440 psi) Increase as needed to achieve a smooth, even spray. Flow rate: 1.5-2.5 litres/min Coating thickness: 155-235 g/m² Recommended nozzle size: 0.43 mm (517 tip) Filter/Mesh: 60–100 mesh, depending on application. Dilution: Dilute with up to 10% water, depending on temperature, humidity, and substrate conditions. Use the minimum amount necessary to maintain good sprayability. Airless spray only. HVLP and other low-pressure systems are not recommended for this product. What’s inside? Water, Acrylic Binder (Soft Emulsion), Pigments (incl. Titanium Dioxide), Fillers (Chalk), Preservative (Isothiazolinone Mixture < 0.1%*), Thickener (Methylcellulose), Dispersant (Phosphate), pH Modifier (Sodium Hydroxide).

Where to use it

Lifestyle Emulsion is perfect for: • Interior walls and ceilings • Previously painted, plastered, wallpapered or primed surfaces • Dry, grease-free surfaces such as wood and plaster Key Facts Coverage: Approx. 10–14 m² per litre Drying Time: Touch dry after 1–2 hours; recoat after 4 hours depending on room temperature and humidity; fully cured after 10 days Colours: Available in our classic colour range Finish: Ultra low sheen Sheen: ~ 2.8% Pack Sizes: 100ml (white only) 2.5L, 5L pH level: 8.8-9.2 Scrub resistance: Class 1 Tools: Brush, roller or spray gun Not suitable for exterior use or surfaces subject to high moisture. Before you start For best results, ensure all surfaces are clean, dry and free from dust, grease or wax. Remove any loose plaster and fill imperfections. Unstable or flaking surfaces should be removed, and glossy or oil-based paints lightly sanded before application.Treat any stains, such as nicotine or water marks, with Earthborn Isolating Primer. Do not apply Lifestyle below 10°C.