Pablo by Coat is a very pale muted warm yellow. Hex: #EEEAE4. RGB: 238, 234, 228. Price: approximately £22.40 per litre. The nearest equivalent from another manufacturer is Dulux Natural Taupe 4 (ΔE 0.5, “identical”), priced at approximately £10.20 per litre. Other close matches include Crown Sail White® (ΔE 0.5) and Earthborn Tom’s Bakery (ΔE 0.5).

Pablo by Coat

Hex: #EEEAE4
RGB: 238, 234, 228
Manufacturer: Coat
Price per litre: £22.40
Price per m² (?): £4.48

Saved on this device — open the palette panel any time to compare or share. Buy a sample

Nearest matches from other manufacturers

Colour	Manufacturer	ΔE	Match quality	Price/L	Price/m² (?)
Natural Taupe 4	Dulux	0.5	Identical	£10.20 (£12.20 less)	£1.57
Sail White®	Crown	0.5	Identical	£8.20 (£14.20 less)	£1.37
Tom’s Bakery	Earthborn	0.5	Identical	£24.00 (£1.60 more)	£4.80
Holland Park (No.No.5)	Mylands	0.5	Identical	£27.20 (£4.80 more)	£3.63
Possibility	Johnstone's	0.6	Identical	£12.36 (£10.04 less)	£2.06
Rich Praline 6	Dulux	0.6	Identical	£10.20 (£12.20 less)	£1.57
Golden Jasmine 4	Dulux	0.6	Identical	£10.20 (£12.20 less)	£1.57
Velvet Truffle 6	Dulux	0.6	Identical	£10.20 (£12.20 less)	£1.57
Linen White (No.LRV 82)	Dulux Heritage	0.6	Identical	£10.40 (£12.00 less)	£1.30

Natural Taupe 4 Dulux

Tom’s Bakery Earthborn

Possibility Johnstone's

Golden Jasmine 4 Dulux

Identical ΔE 0.6

£10.20/L £1.57/m²

Velvet Truffle 6 Dulux

Identical ΔE 0.6

£10.20/L £1.57/m²

Linen White Dulux Heritage

Identical ΔE 0.6

£10.40/L £1.30/m²

Colour neighbourhood

Coverage & application

Manufacturer figures from the Coat Product Advice Sheet. Real-world coverage is typically 15-20% lower.

Finish	Coverage	Coats	Sheen	Scrub class	Touch dry	Recoat	VOC
Eggshell PAS	10 m²/L	2	10%	1	1h	4h	30 g/L
Exterior PAS	10 m²/L	2	20%	1	1h	4h	30 g/L
Flat Matt PAS	10 m²/L	2	2%	1	30 min	2h	2.9 g/L
Flat Matt Claypaint PAS	10 m²/L	2	15%	1	2h	—	2.9 g/L
Floor Paint PAS	10 m²/L	2	20%	1	1h	4h	10 g/L
Soft Sheen PAS	10 m²/L	2	10%	1	2h	4h	30 g/L

Surface preparation by substrate

Eggshell

General application: Stir thoroughly before use. Apply 2 coats of COAT paint by brush or roller or application. If light or bright colours are to be used an additional coat may be required. Tones of separate batches may vary slightly, for colour consistency purchase sufficient paint for the complete job at one time. Preparation of the surface to be painted is vital to the performance of your COAT paint. ● Make good any structural cracks or defects and match the finish to the existing substrate. Use flexible fillers only. ● Wash down and remove old flaking or defective coating. ● A glossy painted surface must be sanded to a matt finish prior to applying the first coat of paint. Avoid the inhalation of dust. Wear a suitable face mask when dry sanding. ● Bare metal requires a suitable primer. ● COAT paints are self-priming, however if a heavily repaired substrate has a wide variation of porosity and colours, priming is recommended as a first coat to create an even base colour. ● For interior use, prime new, bare and porous surfaces using one coat of the appropriate COAT paint, thinned with water (1 part water, 9 parts paint). (Do not apply at temperatures below 5oC).

Exterior

General application: Stir thoroughly before use. Apply 2 coats of COAT paint by brush or roller or application. If light or bright colours are to be used an additional coat may be required. Tones of separate batches may vary slightly, for colour consistency purchase sufficient paint for the complete job at one time. Preparation of the surface to be painted is vital to the performance of your COAT paint. ● Make good any structural cracks or defects and match the finish to the existing substrate. Use flexible fillers only. ● Wash down and remove old flaking or defective coating. ● A glossy painted surface must be sanded to a matt finish prior to applying the first coat of paint. Avoid the inhalation of dust. Wear a suitable face mask when dry sanding. ● Bare metal requires a suitable primer. ● Not suitable for exterior plastic surfaces or decking. (Do not apply at temperatures below 5oC). COAT Trading ltd, 128 City Road, London EC1V 2NX. +44(0) 7368 870 097

Flat Matt

General application: Stir thoroughly before use. Apply 2 coats of COAT paint by brush or roller application. If light or bright colours are to be used an additional coat may be required. Tones of separate batches may vary slightly, for colour consistency purchase sufficient paint for the complete job at one time. Preparation of the surface to be painted is vital to the performance of your COAT paint. ● Make good any structural cracks or defects and match the finish to the existing substrate. Use flexible fillers only. ● Wash down and remove old flaking or defective coating. ● A glossy painted surface must be sanded to a matt finish prior to applying the first coat of paint. Avoid the inhalation of dust. Wear a suitable face mask when dry sanding. ● Bare metal requires a suitable primer. ● COAT paints are self-priming, however if a heavily repaired substrate has a wide variation of porosity and colours, priming is recommended as a first coat to create an even base colour. ● For interior use, prime new, bare and porous surfaces using one coat of the appropriate COAT paint, thinned with water (1 part water, 9 parts paint). (Do not apply at temperatures below 5oC).

Flat Matt Claypaint

General application: Stir thoroughly before use, the high solids nature of this paint requires vigorous stirring. We recommend mechanical stirring where possible. Apply 2 coats of COAT paint by brush or roller application. If light or bright colours are to be used an additional coat may be required. Tones of separate batches may vary slightly, for colour consistency purchase sufficient paint for the complete job at one time. For best results, try to keep a wet edge and complete one wall at a time. Preparation of the surface to be painted is vital to the performance of your COAT paint. ● Make good any structural cracks or defects and match the finish to the existing substrate. Use flexible fillers only. ● Wash down and remove old flaking or defective coating. ● A glossy painted surface must be sanded to a matt finish prior to applying the first coat of paint. Avoid the inhalation of dust. Wear a suitable face mask when dry sanding. ● COAT paints are self-priming, however if a heavily repaired substrate has a wide variation of porosity and colours, priming is recommended as a first coat to create an even base colour. ● For interior use, prime new, bare and porous surfaces using one coat of the appropriate COAT paint, thinned with water (1 part water, 9 parts paint). ● Clay or lime plaster must be moistened prior to painting. (Do not apply at temperatures below 5 oC). COAT Trading ltd, Kemp House, 128 City Road, London EC1V 2NX. +44(0) 7368 870 097

Floor Paint

General application: Stir thoroughly before use. Apply 2 coats of COAT paint by brush or roller or application. If light or bright colours are to be used an additional coat may be required. Tones of separate batches may vary slightly, for colour consistency purchase sufficient paint for the complete job at one time. Preparation of the surface to be painted is vital to the performance of your COAT paint. ● Make good any structural cracks or defects and match the ﬁnish to the existing substrate. Use ﬂexible ﬁllers only. ● Wash down and remove old ﬂaking or defective coating. ● A glossy painted surface must be sanded to a matt ﬁnish prior to applying the ﬁrst coat of paint. Avoid the inhalation of dust. Wear a suitable face mask when dry sanding. ● COAT paints are self-priming, however if a heavily repaired substrate has a wide variation of porosity and colours, priming is recommended as a ﬁrst coat to create an even base colour. ● For interior use, prime new, bare and porous surfaces using one coat of the appropriate COAT paint, thinned with water (1 part water, 9 parts paint). ● Ensure new concrete is thoroughly dried and cured before painting on it. Algae, fungal or mould growth should be removed and treated with a fungicidal wash. Walk on after 24 hours. (Do not apply at temperatures below 5oC).

Soft Sheen

General application: Stir thoroughly before use. Apply 2 coats of COAT paint by brush or roller application. If light or bright colours are to be used an additional coat may be required. Tones of separate batches may vary slightly, for colour consistency purchase sufficient paint for the complete job at one time. Preparation of the surface to be painted is vital to the performance of your COAT paint. ● Make good any structural cracks or defects and match the finish to the existing substrate. Use flexible fillers only. ● Surfaces affected by mould growth should be treated with a fungicidal wash and mould inhibitor and allow to dry thoroughly before painting. ● Wash down and remove old flaking or defective coating. ● A glossy painted surface must be sanded to a matt finish prior to applying the first coat of paint. Avoid the inhalation of dust. Wear a suitable face mask when dry sanding. ● COAT paints are self-priming, however if a heavily repaired substrate has a wide variation of porosity and colours, priming is recommended as a first coat to create an even base colour. ● For interior use, prime new, bare and porous surfaces using one coat of the appropriate COAT paint, thinned with water (1 part water, 9 parts paint). (Do not apply at temperatures below 5oC).

What's on your walls?

Got this colour at home? Let us know.